Consumables


  Consumables > Mechanical Milling >

Carbide End Mills

Carbide End Mills
 
More Views:


Made of solid carbide for maximum performance and durability, carbide end mills are used to cut metal (copper, aluminum, gold, solder, steel, NiCo), circuit board material and other non-metallics.

2-Flute end mills have deeper, longer gullets for greater chip-carrying capacity, are center cutting and are available in diameters as small as 0.05 mm.

4-Flute end mills last longer than 2-flute because wear is distributed over a greater area. They also remove material more quickly, produce finer finishes and can be moved across the sample at a higher rate.

4-Flute, Long Reach end mills feature cutting flutes that extend up from the tip approximately 3x the diameter of the tip to allow cutting into deep cavities.
SAFETY DATA SHEET


Item# Item Name Qty Add
15-922F0.05 Carbide End Mill – Al/Cu, 2-Flute, 0.05 mm Ø x 38 mm L x 3 mm shank (Pk/4)
15-922F0.25 Carbide End Mill – Al/Cu, 2-Flute, 0.25 mm D x 1.5" (38 mm) L x 3 mm shank (Pk/4)
15-922F0.5 Carbide End Mill – Al/Cu, 2-Flute, 0.5 mm D x 1.5" (38 mm) L x 3 mm shank (Pk/4)
15-922F0.7 Carbide End Mill – Al/Cu, 2-Flute, 0.7 mm D x 1.5" (38 mm) L x 3 mm shank (Pk/4)
15-922F1.0 Carbide End Mill – Al/Cu, 2-Flute, 1.0 mm D x 1.5" (38 mm) L x 3 mm shank (Pk/4)
15-922F1.5 Carbide End Mill – Al/Cu, 2-Flute, 1.5 mm D x 1.5" (38 mm) L x 3 mm shank (Pk/4)
15-922F3.0 Carbide End Mill – Al/Cu, 2-Flute, 3 mm D x 1.5" (38 mm) L x 3 mm shank (Pk/4)
15-922FP0.2 Carbide End Mill – PCB, 2-Flute, 0.2 mm D x 1.5" (38 mm) L x 3 mm shank (Pk/4)
15-922FP0.25 Carbide End Mill – PCB, 2-Flute, 0.25 mm D x 1.5" (38 mm) L x 3 mm shank (Pk/4)
15-922FP0.5 Carbide End Mill – PCB, 2-Flute, 0.5 mm D x 1.5" (38 mm) L x 3 mm shank (Pk/4)
15-922FP0.7 Carbide End Mill – PCB, 2-Flute, 0.7 mm D x 1.5" (38 mm) L x 3 mm shank (Pk/4)
15-922FP1.0 Carbide End Mill – PCB, 2-Flute, 1.0 mm D x 1.5" (38 mm) L x 3 mm shank (Pk/4)
15-922FP1.5 Carbide End Mill – PCB, 2-Flute, 1.5 mm D x 1.5" (38 mm) L x 3 mm shank (Pk/4)
15-922FP2.0 Carbide End Mill – PCB, 2-Flute, 2 mm D x 1.5" (38 mm) L x 3 mm shank (Pk/4)
15-922FP3.0 Carbide End Mill – PCB, 2-Flute, 3.0 mm Ø x 1.5” L x 3 mm shank (Pk/4)
15-922FS0.10 Carbide End Mill – Fe, 2-Flute, 0.10 mm D x 1.5" (38 mm) L x 3 mm shank (Pk/4)
15-922FS0.15 Carbide End Mill – Fe, 2-Flute, 0.15 mm D x 1.5" (38 mm) L x 3 mm shank (Pk/4)
15-922FS0.25 Carbide End Mill – Fe, 2-Flute, 0.25 mm D x 1.5" (38 mm) L x 3 mm shank (Pk/4)
15-922FS0.5 Carbide End Mill – Fe, 2-Flute, 0.5 mm D x 1.5" (38 mm) L x 3 mm shank (Pk/4)
15-922FS0.7 Carbide End Mill – Fe, 2-Flute, 0.7 mm D x 1.5" (38 mm) L x 3 mm shank (Pk/4)
15-922FS1.0 Carbide End Mill – Fe, 2-Flute, 1 mm D x 1.5" (38 mm) L x 3 mm shank (Pk/4)
15-922FS1.5 Carbide End Mill – Fe, 2-Flute, 1.5 mm D x 1.5" (38 mm) L x 3 mm shank (Pk/4)
15-922FS2.0 Carbide End Mill – Fe, 2-Flute, 2 mm D x 1.5" (38 mm) L x 3 mm shank (Pk/4)
15-922FS3.0 Carbide End Mill – Fe, 2-Flute, 3 mm D x 1.5" (38 mm) L x 3 mm shank (Pk/4)
15-924F0.7-3 Carbide End Mill – Al/Cu, 4-Flute-LONG, 0.7 mm Ø x 1.5” L x 3 mm shank (Pk/4)
15-924F0.7 Carbide End Mill – Al/Cu, 4-Flute, 0.7 mm D x 1.5" (38 mm) L x 3 mm shank (Pk/4)
15-924F1.0-3 Carbide End Mill – Al/Cu, 4-Flute-LONG, 1 mm Ø x 1.5” L x 3 mm shank (Pk/4)
15-924F1.0 Carbide End Mill – Al/Cu, 4-Flute, 1.0 mm D x 1.5" (38 mm) L x 3 mm shank (Pk/4)
15-924F1.5-3 Carbide End Mill – Al/Cu, 4-Flute-LONG, 1.5 mm Ø x 1.5” L x 3 mm shank (Pk/4)
15-924F1.5 Carbide End Mill – Al/Cu, 4-Flute, 1.5 mm D x 1.5" (38 mm) L x 3 mm shank (Pk/4)
15-924F3.0 Carbide End Mill – Al/Cu, 4-Flute, 3.0 mm D x 1.5" (38 mm) L x 3 mm shank (Pk/4)
15-924FP0.7-3 Carbide End Mill – PCB, 4-Flute-.LONG, 0.7 mm D x 1.5" (38 mm) L x 3 mm shank (Pk/4)
15-924FP0.7 Carbide End Mill – PCB, 4-Flute, 0.7 mm D x 1.5" (38 mm) L x 3 mm shank (Pk/4)
15-924FP1.0-3 Carbide End Mill – PCB, 4-Flute-.LONG, 1.0 mm D x 1.5" (38 mm) L x 3 mm shank (Pk/4)
15-924FP1.0 Carbide End Mill – PCB, 4-Flute, 1.0 mm D x 1.5" (38 mm) L x 3 mm shank (Pk/4)
15-924FP1.5 Carbide End Mill – PCB, 4-Flute, 1.5 mm D x 1.5" (38 mm) L x 3 mm shank (Pk/4)
15-924FP2.0 Carbide End Mill – PCB, 4-Flute, 2 mm D x 1.5" (38 mm) L x 3 mm shank (Pk/4)
15-924FP3.0 Carbide End Mill – PCB, 4-Flute, 3.0 mm D x 1.5" (38 mm) L x 3 mm shank (Pk/4)
15-924FS0.7-3 Carbide End Mill – Fe, 4-Flute LONG, 0.7 mm D x 1.5" (38 mm) L x 3 mm shank (Pk/4)
15-924FS0.7 Carbide End Mill – Fe, 4-Flute, 0.7 mm D x 1.5" (38 mm) L x 3 mm shank (Pk/4)
15-924FS1.0-3 Carbide End Mill – Fe, 4-Flute LONG, 1 mm D x 1.5" (38 mm) L x 3 mm shank (Pk/4)
15-924FS1.0 Carbide End Mill – Fe, 4-Flute, 1 mm D x 1.5" (38 mm) L x 3 mm shank (Pk/4)
15-924FS1.5-3 Carbide End Mill – Fe, 4-Flute LONG, 1.5 mm D x 1.5" (38 mm) L x 3 mm shank (Pk/4)
15-924FS1.5 Carbide End Mill – Fe, 4-Flute, 1.5 mm D x 1.5" (38 mm) L x 3 mm shank (Pk/4)
15-924FS2.0 Carbide End Mill – Fe, 4-Flute, 2 mm D x 1.5" (38 mm) L x 3 mm shank (Pk/4)
15-924FS3.0 Carbide End Mill – Fe, 4-Flute, 3 mm D x 1.5" (38 mm) L x 3 mm shank (Pk/4)
 


Extended Information:

This product can be used with Allied's X-Prep and other mechanical milling machines. Browse our machines >>




You May Also Be Interested In
X-Lube Cutting-Grinding-Polishing Fluid Diamond Grinding Discs Diamond Metal Bond Tools
X-Lube Cutting-Grinding-Polishing Fluid Diamond Grinding Discs Diamond Metal Bond Tools

iframe[id*="spreedly"] { background-color: #FFF; border: 1px solid #CCC; max-height: 17px; padding: 6px 4px; }